Dodge Ram Hub assembly :: Can-Pop Assembly

Dodge Ram Hub assembly

Then remove the axle shaft
  • Comes as a PAIR
  • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • 3 Bolt Flanges
  • Fit 5 Lug Wheels
  • Studs already installed
  • Include sensors
  • Direct replacements
  • Built to strict quality control standards
  • 2 Year Warranty

    This item is backed by a 2 Year Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

    1. Remove the wheel and tire (1:13)
    2. Raise and secure the vehicle.
    3. Remove the lug nuts and then the wheel.
    4. Remove Caliper (1:40)
    5. Turn wheels all the way in the opposite direction of the side you are working on.
    6. Use your socket wrench to remove the caliper bolts.
    7. Use a wire tie to help prevent stress on the caliper.
    8. Use your socket to remove the brackets.
    9. Remove brake disk (3:00)
    10. Take care not to touch the rotor, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
    11. Remove Hub (3:16)
    12. Use a 35mm socket to remove the hub nut.
    13. Give the axle a slight tap with a hammer to loosen it.
    14. Use a pry bar to remove the axle.
    15. Remove the 3 bolts securing the hub using your 18mm socket and extension and ratchet or breaker bar.
    16. You can use penetrating oil to help.
    17. Disconnect your ABS sensor.
    18. Use a rubber mallet to break your hub free, and work around the flange with the hammer to pull it off.
    19. Remove the hub and shield.
    20. Clean up any corrosion with a wire brush.
    21. Install new hub (9:26)
    22. Use some penetrating oil to prep the knuckle for the new hub.
    23. Put the three 18 mm bolts in place and tighten the nuts to 100 ft lbs.
    24. Reinstall the ABS harness.
    25. Replace the axle.
    26. Tighten but don't torque the lug nut.
    27. Put brakes and wheel back on (11:40)
    28. Remember to replace the lug nuts on in a star pattern.
    29. Lug nuts tighten to 120 ft lbs
    30. Hub nut is 185 ft lbs.
    31. Make sure to check your brakes and steering before driving again.

    You might also like

    Dodge Wheel Hub assembly: Ram 2500, Ram 3500
    Dodge Wheel Hub assembly: Ram 2500, Ram 3500
    how to remove a hub assembly on a 1997 dodge ram 1500
    how to remove a hub assembly on a 1997 dodge ram 1500
    Detroit Axle Front Wheel Hub and Bearing Assembly 2002-08 Dodge Ram 1500 W/o Extended Cab 5 Lug W/o ABS
    Automotive Parts and Accessories (Detroit Axle)
    • Placement on Vehicle: Left, Right, Front
    • No ABS
    • 5 Stud, 3 Mating Bolt Holes
    • 4X4, RWD
    • 1 Year Warranty
    Detroit Axle Brand New Front Wheel Hub and Bearing Assembly 2002-06 Dodge Ram 1500 5 Lug W/ ABS 515073
    Automotive Parts and Accessories (Detroit Axle)
    • Placement on Vehicle: Left, Right, Front
    • ABS
    • 5 Stud, 3 Mating Bolt Holes
    • RWD, 4X4
    • 1 Year Warranty

    Copyright © . All Rights Reserved